ADDITIVES

  • FUEL INJECTOR CLEANER

    Description:  Fuel Injection Cleaner is a highly effective combination of active agents for cleaning and protection. This Product is formulated in accordance with the latest standard of fuel and additive technology and meets the Requirement of todays engines, fuels and running conditions. Suitable for all gasoline fuel injection systems such as K, KE and L- jetronic systems etc.

    Application: For Rectifying problem such as difficulties with starting, irregular idling, poor throttle response, performance losses, surges due to lean mixture and poor exhaust values caused by contaminated injection systems. Repeat treatment if problem reoccur. Suitable for all gasoline injection systems. One 300ml can is sufficient for up to 70 ltr of fuel. This product is effective over 2000 km injection .Cleaner can be mixed with fuel at any time since mixing is spontaneous.

    Part NoContentsUnits in Carton
  • INLINE PETROL SYSTEM CLEANER

    Description: 

    In-Line intensive Petrol System cleaner is a ready –to-use highly effective combination of additives for
    cleaning all petrol injection systems such as K, KE, Ljetronic and formulated for use in jet clean units.

    Application: 

    Suitable for all petrol injection systems. For eliminating difficulties with starting idling, poor throttle
    response, and performance looses, lean surging and high pollution values in the exhaust caused by contaminated
    injection systems place automatically.

    Part NoContentsUnits in Carton
  • SPEED UP DIESEL

    Description: 

    Speed up diesel is a new diesel fuel additive for combustion improvement and the faster acceleration
    associated with it, above all in partial load range. Fully compatible with all conventional diesel and biodiesel fuels
    speed up diesel considerably considerably improves vehicle acceleration.

    Application: 

    Add to diesel fuel , especially for vehicle diesel engines as well as suitable for fast vans. For the
    improvement of vechile acceleration and smooth operation.One 300ml can is sufficient for max. 60 liters of diesel fuel.
    Mix the contents of the can with the diesel fuel. Mixing also takes place automatically 

    Part NoContentsUnits in Carton
  • SPEED UP GASOLINE

    Description: 

    Speed up is a state of the art, ash –free fuel additive for improving combustion and acceleration in partial
    load range. Compatible with all gasoline and additive qualities. Speed up considerably improves vehicle
    acceleration.

    Application: 

    Used as an additive in the fuel af all 2 stroke and 4- stroke gasoline engines, especially for motor vehicle
    engines. Also can be used in two-wheeled vehicles . For the improvement of vehicle acceleration and smooth operation.
    One 300 ml can is sufficient for max.70 liters of fuel .Mix the contents of the can with the fuel .Mixing takes place
    automatically.

    Part NoContentsUnits in Carton
  • SUPER DIESEL ADDITIVE

    Description: 

    Super diesel additive contains a mixture of agents with cleaning, dispersing, material –protection and
    cetan –number increasing properties which has been formulated for to days engines, fuels and running
    conditions.The resulting lubricity improver provides better lubricity for diesel fuels low in sulphur. Due to the increased
    ignition performance, the fuel shows better combustion behavior when the engine is cold and the pollution from odours
    in the exhaust gases is reduced suitable for all diesel engines and diesel fuels.

    Application: 

    Added to diesel fuel for all diesel engines particularly in modem high pressure injection such as common
    rail and pumped jet fuel injection engines in passenger and commercial motor vehicles, tractor,construction machinery
    and stationery engiries ideally suitable for preserving engines when decommissioned for long periods under extreme
    conditions. One 300 ml can of the product is sufficient to treat 60 liters of diesel fuel.To keep the injectors clean and for
    corrosion protection, add super diesel additive in passenger vehicle diesel fuel tank every 2,000km.

    Part NoContentsUnits in Carton
  • INLINE DIESEL SYSTEM CLEANER

    Description: 

    Inline Diesel System Cleaner contains a highly effective cleaning combination of additives formulated
    for rapid and cost –effective cleaning of disruptive deposits in the fuel systems of diesel engines. The special additives
    guarantee corrosion protection and protection and increase ignition performances.

    Application: 

    For rectifying problems or for preventive use and cleaning of the fuel system in conjunction with the
    Decarb unit. For all diesel vehicles,including common railand pumped-jet fuel injection. To clean, fill the De-cab unit part
    no.001 with 300ml in line Diesel system cleaner.Further instructions on use are given in the instructions for the Decarb
    unit

    Part NoContentsUnits in Carton
  • OIL TREATMENT

    Description: 

    Oil Treatment is a multi functional high performance additive for reducing friction and wear and
    stabilizing viscosity. It protects engine oil against viscosity loss even under the harshest conditions and protects the
    engine against wear. Oil Treatment is based on the latest additive technology and is compatible with all synthetic and
    mineral engine oils.

    Application: 


    For all gasoline and diesel engines in new and used cars .Can contents (300ml) is sufficient for maximum 5
    liter of engine oil. After adding to the engine oil, allow the engine to run warm. The product can be added at any time.

    Part NoContentsUnits in Carton
  • ENGINE OIL FLUSH

    Description: 

    Engine Flush is a specially formulated combination of additives and carrier fluid in combination with
    the carrier fluid the highly effective detergent and dispersant additives dissolve sludge and lacquer formers. All types of
    oil-soluble and oil insoluble residue are brought into suspension and removed during the next oil change. An
    Engines which has been cleaned of deposits and contamination and which is then filled with fresh oil not
    contaminated with old impurities can develop its full performances characteristics. 

    Application: 

    Cleaning and flushing out the oil circuits of gasoline and diesel engines. The use of engine flush is
    Dependent on the degree of contamination of the oil circuit. Not suitable for use on motorbikes with wet clutches. One
    300ml can is sufficient for up 6 liters of oil. Add engine flush to the motor oil at running temperature before changing the oil.
    After adding the product, allow the engine to idle for approx 10 minutes Then change the oil and the filter. Engine flush is
    compatible with all commercially available motors oils 

    Part NoContentsUnits in Carton
  • RADIATOR FLUSH

    Description: 

    A concentrate specially developed for cooling systems in general but particularly those in motor
    Vehicles dissolve contaminants containing lime and oil in radiators heating systems, pipes and in engine .Modern
    Formula containing complex ants with active cleaning agents.

    Application: 

    Suitable for all cooling water systems in motor vehicles, buses and commercial vehicles. Add contents
    to the Cooling water. Run the heating system. Depending on the degree of contamination, let the engine run
    Approximately 10 

    Part NoContentsUnits in Carton
  • OIL SMOKE STOP

    Description: 

    Oil Smoke stop reduces the oil consumption of gasoline and diesel engines via the piston rings and
    valve guides. It prevents blue smoke and oil mist and acts against the loss in viscosity in motor oils. Oil smoke stop
    Increase the Compression ratio and reduces engine noise. Provides extra protection in engines with high levels of wear.
    Extends the Service life of catalytic converters. 

    Application: 

    For all gasoline and diesel engines. Compatible with all commercially available motor oils. Not
    suitable for Use in motorbikes with wet clutches. One 300 ml can of oil smoke stop is sufficient for 4-6m liters of motor oil.
    Do not add More than 10% .Add to the warm motor oil during every oil change and between oil changes if oil
    consumption is very High. 

    Part NoContentsUnits in Carton
  • RADIATOR ADDITIVE SEALANT

    Description: 

    Radiator additive Sealant is dispersion for sealing leaks in water –cooling systems in motor vehicles.
    The Product reliably seals hair cracks and small leaks. The solids dispersion is stabilized carrier fluid. 

    Application: 

    Used for sealing small leaks in cooling circuits of passenger motor vehicles commercial vehicles ,
    buses and Two-wheel vehicles. Also suitable for cooling circuit with filters. Shake container before use .Run the
    heating System. With the engine running, pour the contents into the cooling fluid at operating temperature and allow
    the engine to continue running for a further 10 minutes. The content is sufficient for 10 liters of coolant. 

    Part NoContentsUnits in Carton
  • EGR CLEANER

    Description: 

    MOTOCHEM is formulated to liquefy and remove even the most stubborn oil deposits and unbumed
    fuel Formed by EGR and PCV gases as the pass through the air intake and intake valves. MOTOCHEM will liquefy
    The deposits allowing them to be burned in the normal Combustion process. 

    Application: 

    For the air intake manifold, inlet valves and EGR valve of all diesel engines. Also recommended to be
    Used at Each service interval to maintain cleanliness possibility to use an extension spray tube with multiple
    Injection holes (Option).

    Part NoContentsUnits in Carton
  • GEAR OIL ADDITIVE

    Description: 

    Gear oil Additive considerably reduces wear and lowers peak temperature. Gear Oil Additive smooth
    out Tooth faces and ensures almost wear –free smooth running operation as well as less harsh shifting. For special
    use in Manual and differential; transmission. 

    Application: 


    Added to motor vehicle manual transmission axle drivers, differential transmissions and mechanical
    Steering systems. Add gear additive to the gear oil –mixing takes place automatically during operation. The product is
    suitable for both mineral and synthetic based gear oils.300ml is sufficient for 1 liter of gear oil. 

    Part NoContentsUnits in Carton
  • AIR INTAKE CLEANER

    Description: 

    Special active solvent for cleaning typical contamination and deposits found in the intake and throttle
    Valve areas. Dissolves and removes all smeary deposits and contaminants such as oil, resins, adhesive residues, etc.
    Also reliably cleans nozzles and internal components. Ensures the operability of all moving parts and reduces fuel
    Consumption 

    Application: To be used for all gasoline engines with MOTOCHEM air intake Cleaner Tool/Equipment.PART NO CONTENTS UNITS IN CARTON

    Part NoContentsUnits in Carton
  • FUEL ADDITIVE (T/W)

    Description: 

    Two wheeler /bike oil Additive is a colloidal, MoS solid-lubricant no deposits,absolutely compatible with all filter 
    systems, reduces running –in and running wear reduces oil and fuel consumption increases engine smoothness, reliability 
    and economy can be used with wet clutches tested for catalytic converter compatibility, compatible with fine filters. 

    Application: 

    Added to engine oil for four –stroke motorbike engines and two –stroke engines with separate lubrication. Can be used 
    with wet multi –disc clutches .For two-stroke engines with mixture lubrication, two wheeler oil additive is added to the 
    petrol –oil mixture. 

    Part NoContentsUnits in Carton
  • OIL ADDITIVE (T/W)

    Description: 

    TFour –Stroke Bike Additive contains and dispersant additives and is specially formulated for four –stroke motorbike 
    engines (aspirated and injection) 

    Application: 

    Protects the fuel systems from corrosion . Normalizes petrol consumption and exhaust values. Reduces Knocking tendency in 
    the engine. Breaks down residues in valves and combustion chamber. Cleans the carburetor and injectors. Increases economy,
    operational reliability and performances .Tested for catalytic converter compatibility ,environmentally friendly.

    Part NoContentsUnits in Carton
  • ENGINE OIL FLUSH (T/W)

    Description: Engine Flush is a specially formulated combination of additives and carrier fluid. 

    Application: 

    One 300 ml can is sufficient for up to 4.5 liters of oil. Add Racing engine flush to the motor oil at running temperature 
    before changing the oil. After adding the product,allow the engine to idle for approximately 10 minutes. Then change the oil 
    and the filter .Two wheeler engine flush is compatible with all commercially available motor oils. Suitable for use
    on motorbikes with wet clutches.

    Part NoContentsUnits in Carton